• Home  / 
  • Coping Saw
  •  /  Steps to Follow when Crown Molding With a Coping Saw

Steps to Follow when Crown Molding With a Coping Saw

Crown Molding has been one of the best techniques that have been used for centuries when it comes to disguising and beautifying the Juncture of the Ceiling and walls. This is one of the techniques that do require you to have not only the skills but also a wide experience hence the beginners in the woodwork are less conversant with it. Despite that if you are a beginner in the wood work techniques then having this technique plays an imperative role in helping you to save a lot. Crown Molding with a Coping Saw is deemed to be one of the easiest tasks that you can perform.

It involves the creation of the Cornice’s curves that at times they are given classical names such as SCOTIA, Cyma, and Ovolo. You have to make a variety of saw cuts such as the coped Joint and the Outside Miter when installing the Crowns. Coping is the process referred when one cuts the end of a molding so as to mimic the profile milled into its face. The Coped Cuts are the one essential during the crown molding process into the inside corner.

Requirements During Crown Molding

  • Pencil.
  • Coping Saw
  • Miter Saw.
  • Tape Measure or Any Other Measurement Tools.
  • Wood or Lumber.

Procedure and Steps

Step One: Crown Installation.

  • This is where you will have to determine the amount of Crown that you will have to buy.
  • You will also take measurements of each wall and make a sketch that is plain of the room.
  • The pieces with a square cut on each end be the first piece that you will have to install. These ends are usually coped with a coping saw. You can also Miter them using the miter saw.

Step 2: Laying Out of The Molding

This is where you determine how each piece of the molding will go up around the room. You will make a drawing of the plan of the room on a piece of paper. When determining the layout, you will have to install the Outside corners last so as to avoid coping both ends of the last length of the molds. You will then mark the position of both ends using the pencil. You will then locate the Studs and Joist and mark their locations with a pencil.

Step Three: Installation of the First Length

You will make the measurements of the Crown Moldings then transfer the measurements to the wood. Using a power miter saw you would cut the molding square at each end. You will then install each length of the Mold in the walls.

Step Four: Cut The Inside Joints

For you to cut the inside Joints, you need a Coping Saw, and the Process of Cutting this ends of the molding is called the Coping Process. You will place the length of the crown upside down on the coping Saw so that the bottom of the mold sits on the wall.

Setting the Coping Saw at 45 Degrees you will swing the saw left for the left side so as to Cope the Corner. You will do the opposite when dealing with the right Corner. Always ensure that the long Point of the Miter is on the back of the Molding and not on the face.

Step 5: Using a Pencil Highlight the Cut Line

After you have Coped the end of the Crown Molding with a Coping Saw you would mark the edge of the face if the Coped Cut using a pencil. This will be used as your Coping Saw Cut Line.

Step 6: Cope the Inside Corner Joint

You will create a snug-fitting Joint by holding your Coping Saw at 5 Degree away from the face of the molding. You will cut a long the pencil marked of your edge. Bring the Molding to the wall and slide it into place so as to check for the tight fit.

You will determine of the uncut ends will land in the inside or outside corner before you can attach your piece to the wall. Using a miter saw you would make a square cut on the mark you had created and the nail your molding up.

Step 7: Mock up An Outside Corner

Take the Measurements of the Coped Piec of the Molding that ends at an Outside Corner and creates a mock-up of the corner from the 12-inch molding Scraps. You will then make an outside miter cut on one piece. Lastly, you will glue and nail the pieces together.

Step 8: Install the Outside Corner

You will butt the side of the Corner into an inside corner. If the corners do not have a butt, then you will make a cut by ensuring that your blade rotates at the opposite 45-degree angle. You will align the Pieces together and glue them

Step Nine: Cutting and Fastening a Return

You will Continue coping the inside Corners as you miter the Outside Corners and assemble your Molding to the wall.

In Conclusion

Crown Molding Can be done effectively as long as you have the right tools. The two essential tools that you should not miss out on when crown Molding is a Coping Saw and Mitering Saw. They are essential when you are Crown Molding. When you are Crown Molding, you are always bound to make a lot of mistakes especially if you are a beginner in the wood work project. Despite that having a through practice on the crown Molding Techniques enables you to increase your efficiency.

Related Posts:

How To Use A Copying Saw For Your DIY Project

Coping Saw Harbor Freight Vs Power Coping Saw

Why A Copying Saw Is Essential For The DIY Projects

All You Need To Know About Coping Saw And Coping Saw Blades

Tips For Selecting A Perfect Coping Saw

5 Best Coping Saw In The Market To Choose From

Leave a comment:

Leave a comment:


Scroll Up